bestsea eyewear craft

Lamination glasses technology allows glasses to have more color choices, and the same pair of glasses is no longer limited to one color. Prior to this, the front frame and temples of a pair of glasses could only use one color at most, for example, the front frame was black and the temples were crystal. The development of eyewear lamination technology has made the color of a pair of glasses more rich and diverse. On the same frame or temple, acetate of various colors can be glued together by lamination cellulose acetate technology, and then After cutting and other processing procedures, a pair of perfect lamination glasses is completed. Now, in addition to the function of glasses as a correcting vision of myopia patients, they are more considered as a part of clothing, especially sunglasses. The emergence of lamination glasses perfectly interprets the definition of glasses as clothing, and also gives beauty lovers more choices.

Different colors of cellulose acetate together through professional technology is a popular glasses technology in recent years. The design concept of this lamination glasses is very simple. The front and the middle bridge, end piece are made of different acetate, and then connected together through the lamination cellulose acetate technology. However, both the middle bridge and the end piece are the stress-bearing parts of the glasses, and the places where they are connected are often fracture. Most factories will avoid these places in order to avoid this problem. In order to solve the problem of cracking, we need to use better glue for bonding, and at the same time use some special lamination techniques.
More colors, more vivid colors, are the effects by many lamination glasses. The glasses are lamination by glue sheets of three colors. The color distribution combined with the bevel design presents a perfect effect. The difficulty in the crafting of this lamination glasses is that the dividing line of each color must be completely distinguished without bleeding. In addition, since each color has bevel with different angles, there is a high requirement for data when carving bevel. At the same time, there are also extremely high requirements for other process in the production of glasses, such as tumbling and polishing.
It takes a lot of skill to make a perfect pair of lamination glasses. Only the perfect lamination cellulose acetate technology can fulfill the original intention of the designer. The temples shown in the picture above has a black acetate at the front and a transparent acetate at the back. The 24K gold copper passes through the temples middle, which looks clear and natural. To achieve this effect, in addition to the perfect lamination skills, the most complicated thing is when the copper passes through the black front section, and the golden copper needle on the transparent acetate has any black, which requires a relatively high Skills and adding some different processes.
Lamination cellulose acetate is a technique. At present, there are not many factories that really master this technology by themselves. They often have to leave this process to some processing factories that specialize in lamination, which brings certain unstable factors to the quality. In our factory, all the lamination processes are done by ourselves. From the selection of acetate, glue, and molds, we must strictly control every process to ensure that the lamination glasses produced are perfect.

More References

更多的拼料工艺参考

L-shaped lamination on both sides of the frame, and one color lamination on the top of the frame. The process requires no color bleeding, accurate carving, and uniform color on both sides, which has a certain degree of difficulty.
This pair of glasses is mainly lamination of front frames, and the yellow acetate seems to pass through the two front frames. In fact, the lamination of the top of the front frame and the middle bridge is completed separately, and the three parts are required to be neatly connected together.
The material of this pair of glasses is composed of two colors, and it seems that a frame is superimposed on it, which increases the layering of the glasses. In terms of craftsmanship, it is required that the ingredients do not bleed, and the fine carving is very accurate.
This is a combination of metal and acetate glasses. The red color on the two sides of the end piece is an extension of the top of the front frame, combined with the texture of metal. The process requires no bleeding, and the color of the two sides is uniform.

CONTACT US

  • Office: No.1515,B RongDe,Huaqiaoxincun Community,Henggang Street, Longgang District,ShenZhen, China
  • Factory: Building 6, Huafeng International Student Industrial Park, Baolong Road, Baolong Street, Longgang District,Shenzhen,China
  • 86-0755-28606637
  • sales@bestseaeyewear.com

NEWS

Introduction to metal injection molding process
This article will take a look at the MIM process, which is often referred to as the metal injection molding process. Som…
How to make special rivet glasses
How to make special rivet glasses? Rivet glasses are one of the most classic glasses, however, most brands of rivets in …
About Crystal Star, A professional lens manufacturer
Crystal Star is a professional lens manufacturer,founded in 2004 and located in Shenzhen, Specialized in the production …
Specially for the pursuit of quality
- our 2024 MIDO eyewear show
The MIDO eyewear show in Italy is one of the most important optical exhibitions in the world.We just brought some of our…
up arrow